The Unist TSL™ system provides smooth and consistent lubrication to the coil, which helps protect tooling and reduces excess waste. The system features controlled lubricant delivery to both sides of thin stock using specialized felt application pads. The TSL™ is capable of applying lubricant coatings as low as 25 mg/ft² (269 mg/m²), and is an ideal solution for applications where proper lubrication is critical. The Unist TSL™ is commonly used for fin stock and thin coils used in the container and packaging industry.
- Protects expensive tooling
- Consistent application at a fraction of the cost of an electrostatic system
- Controlled application of low or no VOC fluids
- Lubricates both sides of stock
- Pneumatic cylinders maintain consistent contact with material
- Reduce fluid usage – apply only what you need
- Eliminate the mess of a dip tank lubrication system
.002″ – .010″ (.05mm – .25mm) thick
in widths from 9″ – 45″ (228mm – 1143mm)
For use with vanishing fluid or low viscosity oil (oils from 30 SUS to 150 SUS).
Not designed for use with water soluble lubricants
SPR-2000™ & The TSL™ System
The patented SPR-2000™ programmable fluid controller is the key component for reliably and accurately controlling the application of lubricants. Precise control of your fluid application saves you money through reduced fluid usage and improves efficiency by ensuring the entire coil is properly lubricated.
The SPR-2000™ alerts you to issues before they become expensive problems that interrupt or stop your production lines. With the SPR-2000™ you’ll know immediately if the fluid supply runs low, if fluid pressure varies, or if flow to the applicator is interrupted (Level, pressure, and flow sensors required). The SPR-2000™ features an intuitive, easy-to-use interface as well as an access code to prevent unauthorized tampering or changes in fluid settings.
- “Set it and forget it” operation
- Easy to use interface
- Access code prevents tampering
- Fault monitoring
Modular Design = Multiple Widths
Lubricant is delivered through separate, modular 9″ manifold blocks combined to lubricate multiple widths.
- TSL™ applicator
- SPR-2000™ programmable fluid controller
- Control valves
- 20 gallon tank
- Integral stand
- Heavy-duty filter
- Pressure switch
- Flow sensors
FREE Bottle of Coolube®
When you buy a Coolubricator, saw system or any other piece of Unist Hardware over and above $1,900.00 we will give you a 3.785 liter bottle of Coolube 2210/2210AL/2210EP absolutely free of charge (valued at $245.00)
Also any customer that buys more than 7 bottles of Coolube 2210/AL/EP will get the 8th one absolutely free of charge, plus free delivery anywhere in Australia.
Also at the same time check out the benefits of using Coolube over other cheaper products that are on the market.
Limited Time Offer!
This offer is only available until June 30 2019. Get in quick to take advantage of our special EOFY deal and save!
Just get in touch by calling Unist on 02 8850 2022.
THIS OFFER ENDS ON THE 30TH OF JUNE 2019
and cannot be used with customers who already receive special pricing.
Changing from Alucobond/Composite panel to Solid Aluminium Sheet
Do you find yourself having to Route 3mm solid Aluminium sheet in preference to Alucobond/Composite panel? If you are experiencing any of the following you need to talk to our John Barker (Managing Director) of Unist Australia.
- Ragged cutting
- Burning out cutters
- Breaking router bits
- Terrible surface finish
- Just the inability to get the job done
We understand your problem, you need to lubricate the routing cutter with our 3 nozzle Coolubricator.
For help on this matter call John Barker on 02 8850 2022 or email [email protected].
Watch a Routing video: https://unist.com.au/routing
The facade industry is moving in part from ACM to Solid Aluminium panels. HVG/Alucobond Architectural are introducing MondoClad, a Pre-finished 3 mm aluminium panel.For more information go to: