Uni-Roller® – S2 Continuous stock lubrication
The Uni-Roller® S2 lubricator is the ultimate solution for continuous stock lubrication. Combined with an SPR-2000™ or SPR-2000 JR™ programmable ﬂuid controller, the Uni-Roller® S2 will consistently apply the correct amount of ﬂuid to both the top and bottom of your coil, day after day.
- Reduce lubricant consumption by 50% or more
- Cleaner floors & work area
- Quick-change rollers for easy maintenance
Uni-Roller® S2 applications:
- Roll forming
- Fine blanking
- Deep drawing
- Application of rust preventives and other protective coatings
Delivers return on investment in less than 6 months
That’s what many of our customers report. By applying the proper amount of fluid, the Uni-Roller® lubricator uses 50 to 90% less lubricant for coil lubrication. Plus it decreases the mess, the parts cleaning, fluid recycling and costs associated with in-die spray systems, rag technology and externally lubricated rollers.
The internally-supplied difference
The internally-supplied rollers are essential to precisely applying the ﬂuid. Inside each of the rollers is a dispenser tube with small holes placed along its length. Fluid is injected into the dispenser tubes from the ﬂuid controller and dispensed across the inside of the rollers.
The lubricant is transferred to the stock through durable polyester felt or polyurethane foam roller covers. These cover materials apply the lubricant smoothly and evenly across both the top and bottom of the stock.
The Uni-Roller® S2 applies the exact amount of lubricant required. This eliminates the mess and waste associated with in-die spray systems and externally lubricated roller systems. The result is not only a cleaner shop, but also significant savings from decreased ﬂuid waste, improved die life, better part quality and increased machine up-time. Many customers have reported savings resulting in a return on investment of less than six months!
The brushed stainless steel guards protect the rollers and guide material when loading coil stock or feeding blanks. With the guards removed for better access, a roller can be changed in about a minute using a single wrench. The Uni-Roller® S2 is built to handle any manufacturing environment without sacrificing ease of maintenance
Built to fit your application
The Uni-Roller® S2 is modular in design. A single roller set is used for widths of 18” [457.2 mm] or less. For stock over 18” [457.2 mm] wide, multiple 12” [304.8 mm] wide roller sets are staggered and overlapped. Standard sizes are available to accommodate common stock widths, with custom sizes available on request.
|Roller coverage||A (extrusion length)||B (overall width)|
|3” [76.2 mm]||12” [304.8 mm]||13.13” [333.5 mm]|
|6” [152.4 mm]||12” [304.8 mm]||13.13” [333.5 mm]|
|12” [304.8 mm]||18” [457.2 mm]||19.13” [485.9 mm]|
|18” [457.2 mm]||24” [609.6 mm]||25.13” [638.3 mm]|
|Roller coverage||A (extrusion length)||B (overall width)|
|23” [596.9 mm]||30” [762 mm]||34.16” [867.75 mm]|
|35” [889 mm]||42” [1066.8 mm]||46.16” [1172.5 mm]|
|46.5” [1181.1 mm]||54” [1371.6 mm]||58.16” [1477.3 mm]|
|58” [1473.2 mm]||66” [1676.4 mm]||70.16” [1782.1 mm]|
|69.5” [1765.3 mm]||78” [1981.2 mm]||82.16” [2086.9 mm]|
Take control with the SPR-2000™
The SPR-2000™ alerts you to issues before they become expensive problems that interrupt or stop your production lines. With the SPR-2000™ you’ll know immediately if the fluid supply runs low, if fluid pressure varies, or if flow to the applicator is interrupted (Level, pressure, and flow sensors required). The SPR-2000™ features an intuitive, easy-to-use interface as well as an access code to prevent unauthorized tampering or changes in fluid settings.
Stock type: coil stock
Stock thickness: .005”-.25” (.13mm – 6.35mm)
Stock width: 3″ – 72″ and up (76mm – 1828mm). Contact Unist.
Fluid type(s): For use with a broad range of water soluble and neat lubricants. Viscosity from 30 – 1000 SUS. Thicker lubricants can be tested by Unist for compatibility.
Fluid supply: pressurized 3 gal(11.4L), 6 gal(22.7L), 15 gal(56.8L), 30 gal(113.6L) tank. Also 20 gal(75.7L) poly tank with diaphragm pump. Also can be integrated into customer’s bulk fluid system
Applicator material: polyester felt or polyurethane foam
Controller: SPR-2000™ or SPR-2000JR™
Power: NA (see SPR-2000™ or SPR-2000 JR™ for controller power requirements)
Mounting: 5/16-18 t-nuts supplied in bottom extrusion slots allow for multiple mounting options. 2 t-nuts per slot provided.
Air: Clean, dry, compressed air, 80-100 psi (5.5-6.9 bar),10 SCFM (280 SLPM) minimum
FREE Bottle of Coolube®
When you buy a Coolubricator, saw system or any other piece of Unist Hardware over and above $1,900.00 we will give you a 3.785 liter bottle of Coolube 2210/2210AL/2210EP absolutely free of charge (valued at $245.00)
Also any customer that buys more than 7 bottles of Coolube 2210/AL/EP will get the 8th one absolutely free of charge, plus free delivery anywhere in Australia.
Also at the same time check out the benefits of using Coolube over other cheaper products that are on the market.
Limited Time Offer!
This offer is only available until June 30 2019. Get in quick to take advantage of our special EOFY deal and save!
Just get in touch by calling Unist on 02 8850 2022.
THIS OFFER ENDS ON THE 30TH OF JUNE 2019
and cannot be used with customers who already receive special pricing.
Changing from Alucobond/Composite panel to Solid Aluminium Sheet
Do you find yourself having to Route 3mm solid Aluminium sheet in preference to Alucobond/Composite panel? If you are experiencing any of the following you need to talk to our John Barker (Managing Director) of Unist Australia.
- Ragged cutting
- Burning out cutters
- Breaking router bits
- Terrible surface finish
- Just the inability to get the job done
We understand your problem, you need to lubricate the routing cutter with our 3 nozzle Coolubricator.
For help on this matter call John Barker on 02 8850 2022 or email [email protected].
Watch a Routing video: https://unist.com.au/routing
The facade industry is moving in part from ACM to Solid Aluminium panels. HVG/Alucobond Architectural are introducing MondoClad, a Pre-finished 3 mm aluminium panel.For more information go to: