menu x
menu x

Tab Stock Lubrication System

Tab Stock System Product Flyer

Tab Stock System
Typical installation of a Unist system lubricating narrow width stock in tab making application

The tab stock lubrication system uses the Unist Mini-Roller™ and is an ideal solution for lubricating narrow coils commonly used in tab making.

When the Mini-Roller™ is combined with the SPR-2000™ controller, the Mini-Roller’s™ patented internally fed design will evenly apply lubricant to both sides of the coil stock. Programmable control ensures consistent lubrication resulting in increased production and decreased downtime.


Tab Live Photo Tab Live Photo2

 

 

 

 

 

 

 

 Full-featured monitoring

The SPR-2000™ provides full-featured monitoring of critical parameters such as fluid level, pressure and flow (optional sensors are required) and alerts users with an audible alarm and red LED. An external alarm relay can also be wired directly to a press control. alarm


Specifications:

Stock type: Aluminum coil stock

Stock thickness: .002″ – 0.10″ (.05mm – .25mm)

Stock width: 1″ – 4″ (25mm – 101mm)

Fluid type(s): For use with vanishing fluid or low viscosity oil (oils from 30 SUS to 150 SUS). Not designed for use with water soluble lubricants.

Applicator material: polyester felt

Fluid supply/capacity: 10 US gal (37L) ASME rated stainless fluid tank

Air supply: Clean, dry, compressed air: 80-90 psi (5.5 – 6.2 bar). 25 SCFM (708 SLPM) minimum

Interface: 4-line x 20 character LCD with 21-button tactile membrane switch

Fluid outputs: max 22/p>

Control inputs: 2 (dry contact/switch closure, prox sensor 10-30 VDC NPN, N.O.)

Alarm inputs: 2 (dry contact/switch closure, prox sensor 10-30 VDC NPN, N.O.)

Outputs: 22 max at power supply voltage. Max power 10 watts/output

Alarm relay: Isolated, non-fused single pole, double throw; 2 amp load max

Max input rate: 50 cycles/sec at 50% duty cycle. Minimum contact open or closed time: 10 milliseconds

Programmable ranges:
Count (CNT): 0-255 counts
Delay (DEL): 0-100 secs (.010 second increments)
Duration (DUR): 0-100 seconds (.010 second increments)

Fuses: Supply: 2 amp, Output: 5 amp

Operating temp. range: 0˚ to +50˚C (+32˚ to +122˚F)

Storage temp. range: -20˚ to +70˚C (-4˚ to +158˚F)

Storage: max 250 setups/jobs

Power: 120VAC – 50/60hz or 240VAC – 50/60hz 9.5 amps

FREE Bottle of Coolube®

When you buy a Coolubricator, saw system or any other piece of Unist Hardware over and above $1,900.00 we will give you a 3.785 liter bottle of Coolube 2210/2210AL/2210EP absolutely free of charge (valued at $245.00)

Also any customer that buys more than 7 bottles of Coolube 2210/AL/EP will get the 8th one absolutely free of charge, plus free delivery anywhere in Australia.

Also at the same time check out the benefits of using Coolube over other cheaper products that are on the market.


Limited Time Offer!

This offer is only available until June 30 2019. Get in quick to take advantage of our special EOFY deal and save!

Just get in touch by calling Unist on 02 8850 2022.

THIS OFFER ENDS ON THE 30TH OF JUNE 2019
and cannot be used with customers who already receive special pricing.

Changing from Alucobond/Composite panel to Solid Aluminium Sheet

Do you find yourself having to Route 3mm solid Aluminium sheet in preference to Alucobond/Composite panel? If you are experiencing any of the following you need to talk to our John Barker (Managing Director) of Unist Australia.

  • Ragged cutting
  • Burning out cutters
  • Breaking router bits
  • Terrible surface finish
  • Just the inability to get the job done

We understand your problem, you need to lubricate the routing cutter with our 3 nozzle Coolubricator.

For help on this matter call John Barker on 02 8850 2022 or email [email protected].

Watch a Routing video: https://unist.com.au/routing

The facade industry is moving in part from ACM to Solid Aluminium panels. HVG/Alucobond Architectural are introducing MondoClad, a Pre-finished 3 mm aluminium panel.For more information go to:

https://hvgfacades.com.au/